Iei 212ilm keypad manual#
Iei 212ilm keypad free#

(Positive voltage coming from the power supply.)

Step 1: Splice together the Blue Relay Common wire from the 212iL harness to the Red wire on the 212iL harness. (Until you supply the common leg of the relay with voltage). This means that there is no voltage running through the relay. The reason is that the 212iL is equipped with a Form C, Dry contact relay on board. If you are sharing the same DC voltage power supply with the 212iL and the magnetic lock, (that is to say if you have only one power supply for both the 212iL and the lock device), you need to run voltage through the common (Blue) wire on the 6 conductor wire harness of the 212iL.

Next you will need to attach the relay wires (white/yellow, blue, and brown) to the wire run that is connected to the locking device. Attach the 6-conductor wire harness to the plug in connector on the back of the 212iL.Ģ. Temperature Tolerance: Standard, -20 ° to 130☏.ġ. Maximum Current Draw allowed voltages: 140mA. Operating Voltages: 12-24 VDC only on input voltage. The 212iL should be mounted to a standard single gang electrical box (with the small slot in the trim ring facing down), but it also is able to mount directly to a flat indoor surface with the provided mounting screws. Be sure that the 212iL is mounted indoors ONLY! Mounting height is the same for an electrical switch, 48' on center. Select the appropriate location for the 212iL. Taking this inventory will familiarize you with the components as well as ensure that you have a complete parts list. Please check the contents of this package and verify all components in the packing list are present. Q Section 1: Unpacking and checking the packing listĢ 1 1/4' black, socket cap flat head machine screwsĢ 1 1/4' black, Phillips flat head sheet metal screws V Programmable 00-99 Second Relay Activation Time

Iei 212ilm keypad manual#

This warranty shall expire two years after shipping date for DOOR-GARD keypads.Įxcept as stated above, IEI makes no warranties, either express or implied, as to any matter whatsoever, including, without limitation to, the condition of its products, their merchantability, or fitness for any particular purpose.Single Unit KeypadControl Installation Manual IEI will not be liable to the purchaser or anyone else for incidental or consequential damages arising from any defect in, or malfunction of, its products. IEI’s sole liability is limited to the repair or (at IEI’s option) the replacement of the defective product or part when sent to IEI’s facility (freight and insurance charges prepaid), after first obtaining IEI’s Return Merchandise Authorization. IEI does not assume any responsibility for damage or injury to person or property due to improper care, storage, handling, abuse, misuse, normal wear and tear, or an act of God.

Iei 212ilm keypad free#

(IEI) warrants its products to be free from defects in material and workmanship, when they have been installed in accordance with the manufacturer’s instructions, and have not been modified or tampered with.

On SE keypad, holes have also been spotted inside the front housing for additional LEDs (LEDs not included).

To speed installation of the SE keypad, holes have been spotted on the inside the back housing for mounting to a wall or a single-gang electrical box.

For use in extreme weather conditions, consult the factory for additional methods of protecting your keypad.

This allows air to circulate and a place for condensation to drain.

Do not seal the drain holes at the bottom of the keypad housing.

Do not silicone the cover plate because the unit will not seal properly. This helps prevent water from entering the case and condensing on the circuit board.

When mounting this unit outside, apply silicone to the area where the wires enter the case.

The bi-color LED provided with the SE keypad illuminates red when the LockRelease relay is de-energized and green when the relay is de-energized.

To avoid ESD (Electro-Static Discharge) interfering with the operation of the keypad, ground the housing to earth ground.